Gold-tone jewelry on production racks at the Miduoduo workshop

Inside Miduoduo · Dongguan, China

PVD Gold
Coating Process.

See how stainless steel jewelry moves through preparation, hanging, ultrasonic cleaning, drying, vacuum-chamber coating and post-coating inspection in our Dongguan workshop. Material, layer structure, thickness and test coverage are confirmed separately by SKU or project.

Real workshop evidenceSeven documented stages

Direct answer

How is PVD gold coating applied to stainless steel jewelry?

At Miduoduo, the documented workflow moves through incoming preparation, fixture hanging, ultrasonic cleaning, drying and pre-coating checks, chamber loading, vacuum coating, unloading and post-coating inspection. The photographs and factory film below document this workshop process.

Watch the workshop workflow

Watch our PVD
coating process.

A 45-second factory film of jewelry preparation, ultrasonic cleaning, drying, chamber setup, vacuum coating and post-coating inspection at Miduoduo.

Open the factory film separately ↗
Miduoduo Jewelry · Dongguan workshop · 45-second production film

Experience from the workshop

The finish is only
part of the story.

This page records what buyers can actually see in Miduoduo’s workshop: preparation, hanging, cleaning, drying, chamber setup, coating and visual inspection. The process record supports factory transparency; product claims still depend on the selected SKU, components and evidence scope.

Chapter I — Surface Preparation for PVD Coating

Before the vacuum chamber

01

Incoming
Cleaning Line

Cleaning line with an operator handling a jewelry rack

Products enter the preparation and cleaning workflow. Pieces and production racks are organized for the next stage.

Hands mounting jewelry on a black production fixture
02

Fixture Selection
& Hanging

The fixture follows the shape of the piece. Our team selects suitable hanging arrangements and mounts the jewelry for processing.

Jewelry racks suspended in an ultrasonic cleaning bath
03

Ultrasonic Cleaning

Racked jewelry passes through ultrasonic cleaning to remove surface residues before drying and coating.

An operator handles a rack inside the drying cabinet
04

Drying &
Pre-Coating Inspection

Cleaned pieces are dried and checked before qualified products move to the vacuum coating area.

Pictured: the drying stage.

Chapter II — Vacuum PVD Coating

Preparation becomes a finish

Where the surface
takes on gold.

PVD stands for Physical Vapor Deposition. In this workflow, the selected finish is applied to prepared jewelry inside the vacuum coating equipment.

An operator prepares racks beside an open vacuum chamber
05

Chamber Loading & Setup

Prepared racks enter the chamber. The operator sets the process parameters for the selected product and finish.

A worker handles gold-tone jewelry at the vacuum chamber
06

Vacuum Coating & Unloading

After the coating cycle, the gold-tone pieces are unloaded and moved forward for inspection.

See the process in motion

45-second factory film · Real production footage

Chapter III — Post-Coating Quality Inspection

After coating, before moving on

An inspector checks gold-tone necklaces over a divided product tray

07 / Post-Coating Inspection

A closer look.
Piece by piece.

The team reviews the appearance and overall finish of the coated jewelry. Qualified pieces continue to the next production stage.

  • ReviewSurface appearance
  • CheckOverall finish condition
  • Move forwardAfter the applicable checks

Factory finish-color reference

PVD finish colors & what the K numbers mean.

All Miduoduo jewelry styles that require a plated-color finish use a vacuum PVD coating process. Natural steel-color options may use a polished stainless-steel surface without a plated-color coating.

Factory PVD finish color reference card showing 14K, 18K and 24K gold-color, rose gold, antique gold, light gold and champagne gold finishes
Factory reference card showing selected 14K, 18K and 24K gold-color, rose-gold, antique-gold, light-gold and champagne-gold appearances. The photographed card does not display every available PVD color.

Confirmed vacuum PVD finish options include black, 14K gold-color, 18K gold-color, 24K gold-color, rose-gold-color, antique-gold-color, light-gold-color, champagne-gold-color, platinum-tone, two-tone and rainbow or iridescent finishes. Exact availability, color matching and production requirements vary by SKU, variant and project.

Black14K Gold-Color18K Gold-Color24K Gold-ColorRose GoldAntique GoldLight GoldChampagne GoldPlatinum ToneTwo-ToneRainbow / Iridescent

How to read 14K, 18K and 24K

These names describe target surface-color appearances on the factory finish reference. They do not mean that the finished coating has a 14K, 18K or 24K gold composition, and they do not mean that the jewelry is solid K gold.

What “990 gold” means

According to the factory plating-process specification, high-purity 990 gold material is used during these confirmed vacuum PVD finish processes. This describes a process input; it is not an independent assay showing that the finished coating is 99% gold.

Evidence scope: the color card and plating-supervisor confirmation document factory finish references and process practice. Exact color, layer structure, thickness, coated components and applicability still need to be confirmed for the selected SKU, variant or custom-production scope.

Proof and evidence scope

Know what the factory evidence proves.

Strong sourcing decisions separate visible process evidence from product-specific specifications and third-party testing.

Documented on this page

  • Workshop preparation and cleaning workflow
  • Fixture hanging and chamber loading
  • Vacuum-coating equipment in use
  • Post-coating visual inspection

Confirm for each SKU or project

  • Base-metal grade and component materials
  • Which components receive the selected finish
  • Coating stack, thickness and color specification
  • Water, wear, nickel-release or restricted-substance evidence
Four process-level Fischer XRF coating measurement records

Four supplied Fischer X-ray fluorescence records, dated April 10, June 26, September 16 and October 24, 2026, document Au/TiN layer measurements for separate coating-process samples. Together they provide 15 readings. They are useful as process-control examples, not as a universal thickness specification for every Miduoduo product. Each reported mean is an average of the measured points in that record; it does not mean every point on a product has the same thickness.

Records reviewed4 records · 15 readingsSeparate measured samples
Reported Au mean range0.030–0.036 μmAcross the four records
Reported TiN mean range0.297–0.540 μmVariation by measured sample
Record dateIdentified scopeAu mean / rangeTiN mean / rangeReadings
Apr. 10, 2026Coating-process record; exact SKU and batch not identified0.030 μm
0.018–0.037 μm
0.540 μm
0.429–0.588 μm
6
Jun. 26, 2026Fischer process record with sample image; exact SKU and batch not identified0.033 μm
0.031–0.035 μm
0.297 μm
0.288–0.314 μm
3
Sep. 16, 2026Fischer process record; exact SKU and batch not identified0.036 μm
0.032–0.039 μm
0.529 μm
0.481–0.577 μm
3
Oct. 24, 2026Earring sample; internal supplier/workshop record, group 6420.036 μm
0.035–0.036 μm
0.481 μm
0.473–0.488 μm
3

What the records show: measured Au and TiN layer values can differ between products and between measurement points on the same product. Product geometry, hanging or coating angle, and inner-versus-outer location can affect the measured result. The reported means are sample-level averages—not proof that every point equals the same value.

Evidence boundary: the supplied records do not identify an exact website SKU or production batch, and they do not establish a point-by-point thickness map for an entire product. Labels such as “23KAu,” “Au/TiN/SuS” and “Au/TiN/SUS” are measurement-application labels and do not independently verify gold karat composition, 18K content or a specific stainless-steel grade. These records also do not establish waterproofing, color-retention life or abrasion performance.

Layer 1 · Process measurement

Four Fischer XRF layer-thickness records

Four separate process records provide 15 Au/TiN readings dated April through October 2026, including one earring sample record.

Recorded range
Au mean 0.030–0.036 μm · TiN mean 0.297–0.540 μm across separate measured samples.
Supports
Process-level layer measurements and evidence that coating thickness can vary by product geometry, hanging or coating angle, inner/outer location, measurement point and production scope.
Does not support
Every SKU, every batch, one fixed thickness at every point, gold karat verification, 18K composition, steel-grade verification, waterproofing, abrasion life or permanent color retention.
Layer 2 · Finished-product compliance

Selected DT066 ring test series

LTI reports LTIT260328A083, LTIT260407A206, LTIT260407A209, LTIT260407A212 and LTIT260407A216 identify Miduoduo as manufacturer and cover different sampled ring groups.

Results
Lead PASS · Cadmium PASS · Nickel Release PASS.
Scope
Selected tested gold- and/or steel-color ring bodies. Reports identify laboratory model DT066; batch and website SKU are not printed in the reports.
Layer 3 · Post-wear nickel release

A583 coated-ring sample

CTI report A2260876957102001 applies EN 12472:2020 wear and corrosion simulation, followed by nickel-release testing under EN 1811:2023.

Results
0.10, 0.71 and 0.68 μg/cm²/week · PASS under the report’s assessment rule.
Does not support
PVD thickness, color-retention life, waterproof performance or independent confirmation of 316 steel composition.
Layer 4 · Exact-model compliance example

P1309 necklace sample

LTI report LTIT260707A055 identifies exact model P1309 and lists seven tested metal components.

Results
Lead PASS · Cadmium PASS · Nickel Release PASS.
Scope
Exact tested P1309 sample and listed components; batch number was not provided. The report does not test PVD process, thickness or steel grade.

How to read the stack: factory photographs prove a workflow; XRF records provide process-level layer measurements; compliance reports cover the stated tested sample and components; material grade requires separate composition evidence. One evidence type must not be used as proof of another.

For jewelry brands & wholesale buyers

Confirm the product—not only the process name.

PVD describes a coating process. A purchase decision should also identify the base material, coated components, finish specification, sample and evidence scope.

01

Material & components

Confirm the base-metal grade and whether posts, backs, clasps, chains or other components use the same material. Explore stainless steel jewelry ↗

02

Finish, sample & thickness

Review the selected style and finish. Where coating thickness is required, ask whether the available data applies to the exact SKU, coated component, inner or outer measurement point, sample, variant or batch. Read the PVD buyer guide ↗

03

Testing & evidence scope

Check whether a document covers the exact SKU, a tested sample, specific components or only a related product family. Read the compliance guide ↗

PVD process and sourcing FAQ

Before you
place an order.

What does this PVD process page prove?

It documents Miduoduo’s visible Dongguan workshop workflow through real photographs and a factory film: preparation, hanging, cleaning, drying, chamber loading, coating, unloading and visual inspection. It does not automatically prove the material grade, coating thickness or test status of every product.

What do the four Fischer coating records show?

Across four separate process records, reported Au layer means ranged from 0.030 to 0.036 μm and TiN layer means ranged from 0.297 to 0.540 μm. These are sample-level averages. Thickness can also differ between points on the same product, including inner and outer surfaces, depending on product geometry, hanging or coating angle and measurement location. The records are not a single catalog-wide or point-by-point product specification.

Does every Miduoduo PVD product use the same coating thickness?

No. Thickness and layer structure can vary by product, production requirement and batch, and different points on the same piece may not measure the same. Use only thickness information that has been measured or specified for the selected SKU, coated component, measurement point, variant or agreed production scope.

Do the Pb, Cd and nickel-release reports verify PVD thickness or stainless-steel grade?

No. Those reports address the stated restricted-substance or nickel-release test scope. They do not verify coating thickness, gold composition, the PVD process or a stainless-steel grade unless those properties are separately tested and stated in the report.

Are all plated-color Miduoduo styles made with vacuum PVD?

Yes. Miduoduo styles that require a plated-color finish use a vacuum PVD coating process. Natural steel-color options may use the polished stainless-steel surface without a plated-color coating. The exact finish color and specification should still be confirmed by SKU and variant.

What PVD finish colors can Miduoduo produce?

Confirmed options include black, 14K gold-color, 18K gold-color, 24K gold-color, rose gold, antique gold, light gold, champagne gold, platinum tone, two-tone and rainbow or iridescent finishes. Availability and color matching vary by product and production scope.

Does an 18K PVD finish mean the jewelry is solid 18K gold?

No. “18K gold-color” describes the target surface appearance. According to the factory process specification, high-purity 990 gold material is used during the confirmed vacuum PVD finish process, but this does not mean that the finished coating has an 18K or 99% gold composition, and it does not mean that the jewelry is solid 18K gold.

Does using 990 gold mean the finished coating is 99% gold?

No. High-purity 990 gold material is a confirmed process input for the stated vacuum PVD finish systems. The finished surface is a multi-material coating system, so the process input cannot be treated as an independent gold-composition assay of the finished coating.

Does this factory workflow prove that a product is waterproof or hypoallergenic?

No. Water, tarnish and sensitive-skin claims depend on the finished product, component materials, coating condition, wear environment and applicable testing. Confirm the available evidence for the selected SKU instead of inferring these claims from the word “PVD.”

What should I confirm before ordering PVD jewelry?

Confirm the SKU, base material, coated components, finish, measurement location where relevant, dimensions, quantity, sample requirements and evidence scope. If coating thickness, nickel-release or restricted-substance documentation matters to your market, state those requirements before order approval.

Can I order samples or source ready-stock PVD jewelry?

Yes. Miduoduo offers selected ready-stock stainless steel jewelry with PVD gold-color finish options and mixed-style ordering. Send your SKU shortlist and quantities to confirm current stock, sample options, product specifications and wholesale pricing. Browse PVD jewelry wholesale.

From process evidence to product selection

Request SKU-level
PVD information.

Share your styles, quantities, target market and the specifications or documents you need. We’ll help you review available products and the evidence scope for your shortlist.

Ready-stock wholesale
Mixed-style sourcing on available products
Private label
Logo MOQ confirmed by style and branding method; packaging quoted separately
OEM / ODM development
Fully custom projects generally from 200 pieces per design

Request SKU-Level PVD Information

Share your target styles, quantity, finish, market and any coating or testing information you need. Fields marked * are required.

We use these details to respond to your inquiry.

Last updated: October 28, 2026 · Reviewed by: Miduoduo Jewelry Sourcing TeamScope: Factory workflow, vacuum PVD finish-color references, process-material explanation, process-level coating measurement, selected finished-product compliance evidence and wholesale buyer verification guidance.
Miduoduo JewelryDongguan, China · Made for your collection